TT126AMC10B is 12.6 inch oled display with full color wide viewing angle screen. It is MIPI interface and resolution is 1600*2560.Outline dimension is 295.11×193.33 mm, thickness is 2.43 mm. Active area is 271.4112×169.632 mm. This oled display is coming out with 70 pins definition. Operating Temperature is -20~70℃, Storage Temperature is -40~80℃.
DRAWING
SPECIFICATIONS
| General Specification | |
|---|---|
| Part No. | TT126AMC10B |
| Outline Dimension(mm) | 295.11×193.33×2.43 |
| Active Area(mm) | 271.4112x169.632 |
| Number of Pixel(pixels) | 1600(W)xRGBx2560(H) |
| Operating temperature(°C) | -20 ~ +70℃ |
| Storage temperature(°C) | -40 ~ +80℃ |
| Display Mode | AMOLED |
| Brightness | 400nits |
| Interface | MIPI 4 Lane |
| Driver IC | RM69380 (COF) / RM692E6 |
| Contrast Ratio | 100000:1 |
| Display color | 16.7M (RGB x 8bits) |
| Pixel arrangement | Real RGB arrangement |
| CN1 Pins Description | ||
|---|---|---|
| Pin No. | Symbol | Description |
| 1 | NC | No connect |
| 2 | NC | No connect |
| 3 | GND | Ground |
| 4 | TP_Report_EN | Reserve pin ,lf not used, please open this pin. |
| 5 | TP_RST | Reset pin for touch, active low |
| 6 | TP_INT Sensorhub | Reserve pin ,lf not used, please open this pin. |
| 7 | TP_INT for AP | Interrupt pin for Touch |
| 8 | TP SPI_CS0 | SPI Chip select pin for TP |
| 9 | TP_SPI_SCK | SPI Clock pin for TP |
| 10 | TP_SPI_MOSI | SPI MOSI pin forTP spi |
| 11 | TP_SPI_MISO | SPI MISO pin forTP spi |
| 12 | GND | Ground |
| 13 | TSP_SDA | Reserve pin |
| 14 | TSP_SCL | Reserve pin |
| 15 | TPIC_CLK | Reserve pin |
| 16 | TSP_1.8V | Reserve pin |
| 17 | TSP_3.3V | TP AVDD power |
| 18 | GND | Ground |
| 19 | DSI1_D3_N | DSI-D3- of Slaver IC MIPI |
| 20 | DSI1_D3_P | DSI-D3+ of Slaver IC MIPI |
| 21 | GND | Ground |
| 22 | DSI1_D2_N | DSI-D2- of Slaver IC MIPI |
| 23 | DSI1_D2_P | DSI-D2+ of Slaver IC MIPI |
| 24 | GND | Ground |
| 25 | DSI1_CLK_N | DSI-CLK- of Slaver IC MIPI |
| 26 | DSI1_CLK_P | DSI-CLK+ of Slaver IC MIPI |
| 27 | GND | Ground |
| 28 | DSI1_D1_N | DSI-D1-of Slaver IC MIPI |
| 29 | DSI1_D1_P | DSI-D1+ of Slaver IC MIPI |
| 30 | GND | Ground |
| 31 | DSI1_D0_N | DSI-D0- of Slaver IC MIPI |
| 32 | DSI1_D0_P | DSI-D0+ of Slaver IC MIPI |
| 33 | GND | Ground |
| 34 | ERR_FG | Output pin used to monitor display driver state and error status MIPI'S HSDT |
| 35 | EL_I2C_SCL | (I2C) SCL clock I/O pin for PMIC |
| 36 | EL_I2C_SDA | (l2C) SCL data 1/O pin for PMIC |
| 37 | 1.8V | VDDI for DDIC |
| 38 | 1.8V | VDDI for DDIC |
| 39 | 1.8V | VDDI for DDIC |
| 40 | DP_ID0 | Output pinof DP_ID0,conncet 1.8V |
| 41 | DP_ID1 | Output pinof DP_ID1,conncet GND |
| 42 | NC | No connect |
| 43 | E_AVDD | Power supply for DDIC Analog system |
| 44 | NC | No connect |
| 45 | GND | Ground |
| 46 | (AVDD,Vint)_EN | Power IC enable control pin, |
| 47 | EN_OLED/Swire | Swire protocol setting pin of power lC |
| 48 | NC | No connect |
| 49 | NC | No connect |
| 50 | ELVSS | ELVSS for OLED |
| 51 | ELVSS | ELVSS for OLED |
| CN2 Pins Description | ||
|---|---|---|
| Pin No. | Symbol | Description |
| 1 | ELVSS | ELVSS for OLED |
| 2 | ELVSS | ELVSS for OLED |
| 3 | ELVSS | ELVSS for OLED |
| 4 | ELVSS | ELVSS for OLED |
| 5 | ELVSS | ELVSS for OLED |
| 6 | NC | No connect |
| 7 | ELVDD | ELVDD for OLED |
| 8 | ELVDD | ELVDD for OLED |
| 9 | ELVDD | ELVDD for OLED |
| 10 | ELVDD | ELVDD for OLED |
| 11 | ELVDD | ELVDD for OLED |
| 12 | ELVDD | ELVDD for OLED |
| 13 | ELVDD | ELVDD for OLED |
| 14 | NC | No connect |
| 15 | VDD 3.3V | Power supply for DDIC Analog circuit |
| 16 | VDD 3.3V | Power supply for DDIC Analog circuit |
| 17 | VDD_3.3V | Power supply for DDIC Analog circuit |
| 18 | VDD_3.3V | Power supply for DDIC Analog circuit |
| 19 | NC | No connect |
| 20 | GND | Ground |
| 21 | GND | Ground |
| 22 | GND | Ground |
| 23 | Bist_Enable | Reserve pin , lf not used, please open this pin. |
| 24 | NC | No connect |
| 25 | NC | No connect |
| 26 | NC | No connect |
| 27 | MTP_PWR_L | MTP programming power supply pin (6V typical)Must be left open or connected to DVSS in normal condition. |
| 28 | NC | No connect |
| 29 | NC | No connect |
| 30 | PCD_L | Pins for PCD function |
| 31 | NC | No connect |
| 32 | NC | No connect |
| 33 | RESX | Reset pin for DDIC, active low |
| 34 | NC | No connect |
| 35 | TE_L | Tearing effect output pinto synchronize MCU to frame writing. |
| 36 | GND | Ground |
| 37 | DSI0_D3_N | DSI-D3- of Master IC MIPI |
| 38 | DSI0_D3_P | DSI-D3+ of Master IC MIPI |
| 39 | GND | Ground |
| 40 | DSI0_D2_N | DSI-D2- of Master IC MIPI |
| 41 | DSI0_D2_P | DSI-D2+ of Master IC MIPI |
| 42 | GND | Ground |
| 43 | DSI0_CLK_N | DSI-CLK-of Master IC MIPI |
| 44 | DSI0_CLK_P | DSI-CLK+ of Master IC MIPI |
| 45 | GND | Ground |
| 46 | DSI0_D1_N | DSI-D1- of Master IC MIPI |
| 47 | DSI0_D1_P | DSI-D1+ of Master IC MIPI |
| 48 | GND | Ground |
| 49 | DSI0_D0_N | DSI-D0- of Master IC MIPI |
| 50 | DSI0_D0_P | DSI-D0+ of Master IC MIPI |
| 51 | GND | Ground |
| TP Pins Description | ||
|---|---|---|
| Pin No. | Symbol | Description |
| 1 | GND | Ground |
| 2 | TP_HSYNC | Synchronous signal Hsync(TYP1.8V),It is used to Improve Huawei's active pen experience,connect to Tcon's Pin TCON needs to output Hsync signal to TP IC at the right time. |
| 3 | AVDD | Analog Power Supply(TYP.3.3V) |
| 4 | TP_VSYNC | Reserve pin |
| 5 | AVDD | Analog Power Supply(TYP.3.3V) |
| 6 | TP_RST | TP reset(1.8V) |
| 7 | TP_Report_EN | Reserve pin |
| 8 | TP_INT for AP | TP_INT for AP(1.8V) |
| 9 | TP_INT_Sensor hub | Reserve pin |
| 10 | GND | Ground |
| 11 | TP_SPI_CS0 | TP Slave select for SPI(Serial Peripheral Interface)(1.8V) |
| 12 | TP_SPI_SCK | TP Slave clock forSPI(Serial Peripheral Interface) |
| 13 | TP_SPI_MOSI | TP Master output, slave input forSPI(Serial Peripheral Interface)(1.8V) |
| 14 | TP_SPI_MISO | TP Master input, slave output forSPI(Serial Peripheral Interface)(1.8V) |
| 15 | GND | Ground |
| 16 | GND | Ground |
| 17 | TSP_1.8V | Reserve pin |
| 18 | TSP_1.8V | Reserve pin |
| 19 | TSP_1.8V | Reserve pin |
